ABSTRACT:

A trial stope was mined in a massive pyrite orebody using draft and fill. Instrumentation was installed to indicate the behaviour of the rock mass as the dimensions of the stope increased. From the study it was concluded that no significant loosening occurs in the stope back at dip spans less than 20m but as the dip span increases above 20m significant loosening initiates in the back to heights of up to 5m. These results indicated that pre-reinforcement of the back may be required where dip spans are expected to exceed 20m. In parallel to this study, an investigation of stope stability predicted by empirical methods was carried out. The empirical models indicated that in massive pyrite, dip spans in excess of 27m would probably require pre-reinforcement with cable bolts. Those stopes with dip spans exceeding 70m could anticipate serious ground control problems, despite cable bolts and would require pillars.

RESÜMEE:

In einen Block aus massivem pyriderzgestein wurde mittels Treiber und Fueller ein Versuchsstollen getrieben. Die Untersuchung zeigte, dass es bei Neigungsweiten von weniger als 20m zu keiner signifikanten Lockerung im hinteren Stollenbereich kommt, bei Neigungsweiten von mehr als 20m ist jedoch im hinteren Bereich eine Lockerung in einer Höhe bis zu 5m festzustellen. Diese Ergebnisse lassen eine Vorverstarkung des hinteren Bereichs fuer angebracht halten, wo Neigungsweiten von mehr als 20m zu erwarten sind. Parallel zu dieser Untersuchung wurde eine weitere untersuchung mittels empirischer Verfahren durchgefuehrt, um die vorhersehbare Stollenstabilitat zu bestimmen. Die empirischen Modelle zeigen, dass bei massivem Pyritgestein, Neigungsweiten von mehr als 27m wahrscheinlich eine Vorverstarkung mittels Kabelbolzen erforderlich machen. Bei Stollen mit Neigungsweiten von mehr als 70m darf vermutet werden, dass trotz Kabelbozen ernsthafte Bodensicherungsprobleme auftreten könnten; in diesem Falle muessten in der Auslegung Pfeiler vorgesehen werden.

RÉSUMÉ:

Une chambre pilote a ete efectuee dans un gisement de pyrite massive avec le methode "drift and fill". Des instrument on ete instales a fin de nos indiquer l'evolution du comportament de la masse rocheuse avec l'augmentation des dimensions de la chambre. De cette etude on est arrivee a la conclusion que pur des chambres jusqu'à 20m de portee le relachement des roches du toit est pratiquement nul, tandis que pur les chambres de plus de 20m d'importants relachements sont verifies sur les roches du toit sur une hanteur de 5m à l'interieur de la masse. Ces resultats montrent que le toit doit être renforce pour des chambres de plus de 20m de portee. En paralelle avec cette etude on a appliquee des methodes empiriques à fin de prevoir la stabilite des chambres. Les modeles empiriques out montre que dans de la pyrite massive pour les chambres de plus de 27m de portee des renforts avec des cables servient probablement necessaires. Pour des chambres de plus de 70m de portee de serieux problemes de control des masses pourraient apparaitre malgre l'instalation de cables. Des piliers seraient à ce moment la conseilles.

1 INTRODUCTION

Neves Corvo began production in 1989 with a start up rate of approximately 1 million tonne per annum. Development work has been carried out since 1982 when the shaft sinking and ramp development was initiated. The mine is currently operating to the 550m elevation (670m below surface) at a capacity of 1.7 million tonne per year of combined copper and tin ore. Access into the orebody was minimal prior to start up in 1989, hence experience of the ground conditions in Neves Corvo was severely limited. To improve the understanding of ground conditions, a trial stope was mined on 780m level approximately 450m below surface. Instrumentation was installed to provide data on the behaviour of the back as the span of the stope increased.

This content is only available via PDF.
You can access this article if you purchase or spend a download.