..., industrialization, assembly and installation of the new generation ETH-PiP 2.0 which forms part of the Fenja field development. asset and portfolio management eth-pip europe government controls and umbilicals cable sub-sea system upstream oil & gas norway government assembly termination assembly...

... joined by two beams, forming an open box structure into which the instrumentation and indenter beam assembly is situated. Height of the indenter beam relative to the test sample mounting area is infinitely adjustable via a set of 1" thick steel plates. Two bolt patterns are arranged in each of eight...

... into the existing wellbore using directional assemblies, usually after a sidetrack operation up hole. This process of trying to breach into the existing well can be problematic and result in multiple unsuccessful attempts, driving up operational spend. Rather than leaving an intersect to chance, a whipstock can...

... in the umbilicals and subsea distribution systems to a remote and passive optical multiplexer and circulator assembly deployed in the optical flying lead (OFL) or optical feedthrough system (OFS) of the subsea tree. This enables the down-going transmission fiber to be split into three sensing fibers which...

...), simulated assembly and operation of equipment in a virtual involvement, and integrated multiplatform optimization software were leveraged for rapid final product development with minimal need for physical testing. To push design ratings to HPHT levels, it was necessary to implement new patented technologies...

... trialed in a well, to verify the results and validate the theory. A jetting tool assembly was developed, with the goal to improve clean-up by impelling acid through the screens and against the filtercake, adding agitation (previously unavailable through soaking placement) leading to a more thorough...

... the rate at which offshore renewable energy can be constructed. The primary areas of focus are: Platform designs that allow for in-port assembly of the structure. Alternatives to the current wind turbines and the heavy lifts they require Alternative offshore methods of assembling current systems...

... bolt as it's mill to whipstock interface, whereas this system uses a self-aligning cylinder that can be assembled on the rig floor or can be pre-assembled in the shop prior to being loaded out. The benefits of being pre-assembled allows for the system to be picked up and directly installed...

... feature running tool climate change completion equipment orientation deployment tubing hanger vxt tooling suite novel thor technology american petroleum institute wellhead requirement field layout assembly offshore technology conference Introduction The THOR technology...

... and pressure along the wellbore. deffenbaugh magnetic field data assembly well logging microcontroller dissolvable weight log analysis calibration test intelligent logging platform sensor ball upstream oil & gas pressure sensor deployment electronics release actuator architecture...

... barrier valve for temporary and workover isolation; a combination of open hole expandable; oil swellable packers for zonal isolation; 6 ⅝" blank tubing in front of the upper zone; a short seal bore extension; a 7 ⅝" sliding sleeve; some spacers; a seal bore packer. This assembly is run in hole after...

... of the 12 -1/4-in. casing and centralizers, but also produce a 9 -7/8-in. window while minimizing any dogleg for future drilling and completion assemblies. The system had to have a proven track record and also have the flexibility to run either mechanically or hydraulically. Because the ID of the casing...

... basins. Offshore execution in Australia involved the installation of large diameter steel pipe sections assembled with merlin connectors and the largest submersible pumps of their kind inside the FLNG Hull. Bespoke installation aids were used such as an over-the-side Riser Assembly Tower. Successful...

... to failure to replace the seal assembly. Full-scale testing demonstrates the system under simulated drilling conditions. Seal life observed at over 200 rotating hours, outlasting most deepwater MPD hole sections. First active sealing device integrated into deepwater drillship. Multi-modal seal control system...

... was considered. Stacking a multi-zone system required some changes to the uppermost zone of the lower stack. This particular multi-zone system requires approximately 75 ft of sump packer seal assembly to house the shifters for the frac circulation sleeves of the lower zone. The shifters are housed in 5...

... requirement coupler hpht fixture interface thd valve artificial intelligence subsea production equipment high pressure high temperature assembly operator completion qualification failure mode hpht subsea production tree exposure engineer OTC-30519-MS , " VXTe Deepwater Tree...

... assembly International Association of Oil & Gas Producers, S-561 (Supplementary Specification to API 171) Subsea Trees) . Barclays, PC Oil Roadmap — July 2018 , "Deep Dive into Deepwater Economics." ANSI/API Specification 6A, Twentieth Edition, October 2010: Specification...

... automotive industry back panel supplier engineer baker hughes application power supply requirement configuration innovation upstream oil & gas assembly strategic planning and management part number reliability harness offshore technology conference product development complexity...

... further contributes to product optimization and successful project execution. subsea architecture subsea system upstream oil & gas jumper stimulation module functionality installation floating production system universal retrofit package interface choke body operation assembly...

... parameters Conventional design and design-optimization techniques typically do not apply for AM part design. The flexibility of AM in generating complex shapes implies reduced number of components and implicit savings in assembly. Also, the possibility of lattice structure generation implies...