1-20 of 115
Keywords: injection rate
Close
Sort by
Proceedings Papers

Paper presented at the SPE/IATMI Asia Pacific Oil & Gas Conference and Exhibition, October 12–14, 2021
Paper Number: SPE-205685-MS
... for higher flowrates. This corresponds to MRF values calculated in the laboratory analysis. Therefore, stronger and more stabilized foam were generated using higher injection rates. Lower and higher flowrates had distinctive set of foam parameters. The acceptable matches for differential pressure, oil, water...
Proceedings Papers

Paper presented at the SPE/IATMI Asia Pacific Oil & Gas Conference and Exhibition, October 12–14, 2021
Paper Number: SPE-205662-MS
... that a separator pressure reduction of 30 psi in Platform 1 has a potential gain of ∼300 BOPD, which is aligned with the field results. Apart from that, there was also a potential savings in gas by utilizing the predicted allocated gas lift injection rate. well performance production control artificial...
Proceedings Papers

Paper presented at the SPE/IATMI Asia Pacific Oil & Gas Conference and Exhibition, October 12–14, 2021
Paper Number: SPE-205596-MS
... oil production enhanced recovery well intervention injector workflow facility management wrfm opportunity identification watercut visualization dashboard producer production monitoring wof module downhole intervention upstream oil & gas attic oil column injection rate Introduction...
Proceedings Papers

Paper presented at the SPE/IATMI Asia Pacific Oil & Gas Conference and Exhibition, October 12–14, 2021
Paper Number: SPE-205542-MS
.... carbonate reservoir carbonate acidizing injection rate upstream oil & gas pvbt profile reaction rate hcl high dissolving-power retarded acid recipe acid recipe complex reservoir concentration retarded acid recipe indiana core plug recipe petroleum engineer emulsified acid hcl equivalent...
Proceedings Papers

Paper presented at the SPE/IATMI Asia Pacific Oil & Gas Conference and Exhibition, October 12–14, 2021
Paper Number: SPE-205575-MS
... of polymer flooding. chemical flooding methods injector polymer concentration water cut enhanced recovery viscosity producer well breakthrough producer heavy oil polymer pilot injection rate upstream oil & gas degradation polymer flooding active bottom water drive bechraji polymer...
Proceedings Papers

Paper presented at the SPE/IATMI Asia Pacific Oil & Gas Conference and Exhibition, October 12–14, 2021
Paper Number: SPE-205631-MS
... in unconventional shale gas field. shale gas hydraulic fracturing completion micro-seismicity data hydraulic fracture upstream oil & gas extended finite element modeling injection rate hydraulic fracturing underburden formation horizontal stress shale gas formation hydraulic fracturing...
Proceedings Papers

Paper presented at the SPE/IATMI Asia Pacific Oil & Gas Conference and Exhibition, October 12–14, 2021
Paper Number: SPE-205650-MS
...) Connectivity solver module – where connectivity between injectors and producers is quantified using a 2 year history match period, 2) Fractional Flow solver module – where oil rates are established as a function of injection rates, 3) Verification module – which is a blind test to assess history match quality...
Proceedings Papers

Paper presented at the SPE Asia Pacific Oil & Gas Conference and Exhibition, November 17–19, 2020
Paper Number: SPE-202218-MS
... the sedimentation of single particle. Simulation of sand production process is conducted and the effect of cementation type, cementation strength and injection rate are investigated. During the simulation, sand particles will detach from the reservoir and the formation will reach a steady state after a period...
Proceedings Papers

Paper presented at the SPE Asia Pacific Oil & Gas Conference and Exhibition, November 17–19, 2020
Paper Number: SPE-202249-MS
... into deepwater reserves. Common mitigation measures for hydrate formation and plugging include the traditional control methods of injecting thermodynamic inhibitor that assure the operational conditions are outside the hydrate risk region. However, inhibitor injection rates are typically designed based...
Proceedings Papers

Paper presented at the SPE Asia Pacific Oil & Gas Conference and Exhibition, November 17–19, 2020
Paper Number: SPE-202340-MS
... time system optimization problem global constraint well model implementation scenario upstream oil & gas optimization operation injection rate production rate valve gas lift diagnostic water cut gas injection rate Introduction The field under study is one of largest fields...
Proceedings Papers

Paper presented at the SPE Asia Pacific Oil & Gas Conference and Exhibition, November 17–19, 2020
Paper Number: SPE-202313-MS
... to allow remote injection control and monitoring. Each well has three zones. One of the iWAG wells was installed with the DTS cable behind casing. This enabled the injection profile monitoring across each sand in order to optimize the injection rate distribution and representatively amongst the four wells...
Proceedings Papers

Paper presented at the SPE Asia Pacific Oil & Gas Conference and Exhibition, November 17–19, 2020
Paper Number: SPE-202333-MS
... fracturing pressure. The viscosity of water and CO 2 increases during cooling of the near wellbore zone; thus, pressure build up grows faster in the case of lower injection temperatures. Although the bottom-hole pressure becomes higher, injection rate is constrained by well head pressure. Heat exchange...
Proceedings Papers

Paper presented at the SPE Asia Pacific Oil & Gas Conference and Exhibition, November 17–19, 2020
Paper Number: SPE-202335-MS
... simulation injection well storage complex reservoir gas reservoir enhanced gas recovery injection upstream oil & gas co 2 production well gas recovery adsorption porosity injection rate fracture unconventional gas reservoir ch 4 adsorption capability australia Introduction CO 2...
Proceedings Papers

Paper presented at the SPE/IATMI Asia Pacific Oil & Gas Conference and Exhibition, October 29–31, 2019
Paper Number: SPE-196281-MS
... Upstream Oil & Gas modular offshore stimulation system spra Injection Rate flow in porous media production enhancement offshore stimulation system stimulation treatment wormhole Arabian Gulf hot offshore well diverter Silurian Dolomite particulate experiment lpfd emulsified acid case...
Proceedings Papers

Paper presented at the SPE/IATMI Asia Pacific Oil & Gas Conference and Exhibition, October 29–31, 2019
Paper Number: SPE-196540-MS
... with the existing techniques, still high breakdown pressure present a persistent challenge. Increasing the injection rate of the fluid into the rock corresponded to a lowering of the breakdown pressure. The higher injection rate allows more fluid to enter the shale porosity thus transmitting the injection pressure...
Proceedings Papers

Paper presented at the SPE/IATMI Asia Pacific Oil & Gas Conference and Exhibition, October 29–31, 2019
Paper Number: SPE-196460-MS
... and produced water salinity (b) Correlation in injection rate trends and produced liquid rate trends, (c) Clear jump in producer ESP intake pressure trends as a sign of response from injection. Machine learning was used to cluster producers based on their produced water salinity trends which enabled...
Proceedings Papers

Paper presented at the SPE/IATMI Asia Pacific Oil & Gas Conference and Exhibition, October 29–31, 2019
Paper Number: SPE-196484-MS
... rate workflow Injection Rate requirement fdp study gas injection artificial lift planning water saturation candidate screening saturation Introduction Artificial lift aims at maintaining oil production, extending asset life and meeting or exceeding the Field Development Plan (FDP...
Proceedings Papers

Paper presented at the SPE/IATMI Asia Pacific Oil & Gas Conference and Exhibition, October 29–31, 2019
Paper Number: SPE-196534-MS
... neglects fluid infiltration movement into the reservoir, resulting in a high number of gas lift mandrels required which in turn, lower gas lift operating pressure and gas lift injection rate. Therefore, an innovation for gas lift spacing design is necessary to optimize gas lift performance. Abstract...

Product(s) added to cart

Close Modal