... is being collected from the de-gasser vessel and is pumped directly into the injector wells through a separate controlled piping and pumping system. This is an advantage to reservoir management especially if the produced water is being extracted from the same reservoir. Unless the water is feeding...

... water injection is less critical since injected water volumes can be made up or "banked" in advance. The subsea system uses a drill center approach, integrating water and gas injection systems. Single water and gas injection flowlines run to the drill centers for injectors. Allocation of gas...

... geology modeling & simulation climate change reservoir injection surface facility injector breakthrough time production stream sequestration producer tscf Notably, this study introduces an innovative storage technique termed "in-situ," evaluating its feasibility for implementation...

... kpa hydrate prediction flow in porous media production monitoring geological subdiscipline injection saturation calculation subsurface storage reservoir surveillance production control hydrate generation modeling economic geology thermal conductivity injector carbon dioxide hydrate...

... injector I3 and producers A1, I1 as well as A5 are relatively high, which is an indication of a potential thief zone. Primary slugs of gel injection are designed for all injectors with channeling effects. The CMOST evaluation results show that the optimal formula of strong primary slug is polymer...

... enhanced recovery communication field injector category information Introduction & Background D Field is located in the west-central Malay Basin, offshore Peninsular Malaysia. The field structure is an elongated, westward plunging anticline. The major NS trending normal faults system...

... production and effective CO 2 storage volume as main objective parameters were optimized. A full compositional dynamic model with proper CO 2 storage features was constructed. The recycling option of produced CO 2 was activated between gas producers and CO 2 injectors in the model. Two CO 2 tracers...

... injector locations were targeted at the high permeability-thickness (KH) location based on reservoir simulation model. However, the optimization of injection with many layers in depleted reservoirs is cumbersome and required up to millions of simulation runs which is not possible to be performed. Therefore...

... ensemble forecasting producer ensemble reservoir characterization iteration saturation enhanced recovery workflow objective ensemble-based approach injector Introduction to Field B Reservoir Setting & Development The S reservoirs in Field B are comprised of up to 52 stacked...

... scope of work: drilling new wells of producers and injector, work-over on existing producer and/or injector wells to establish waterflood pattern, and Water Treatment Injection Plant (WTIP) upgrading. The objective of this paper is to deliver several focuses: (1) Front-to-end workflow of waterflood...

... Abstract Delta Area-X is the newest steam flood project in Delta Heavy Oil Field in Riau Province of Sumatra, Indonesia. The area currently produces 12,000 BOPD from 450 oil producers and 145 steam injectors that are supported by high proactive optimization that consists of steam cyclic...

... production contribution, minimizing the crossflow tendency from Bekalo reservoir that has contrast influx due to its significantly better reservoir property and driving mechanism. It was balanced by injection strategy by adding single sand Tenares injector to maximize the injection allocation towards Tenares...

... Abstract Field A begun water injection in 2016 via four water injector smart wells, which were equipped with Permanent Downhole Gauges and Inflow Control Valves. The water injection module was housed on a rented MOPU due to space limitation. Amidst the study to revamp the reservoir management...

... souring producer history matching reduction srp wx2l injector injection reservoir souring simulation prediction modelling study Introduction Reservoir Souring is the process of Hydrogen Sulfide (H 2 S) generation due to bioactivity of sulphate reducing bacteria (SRB) and archaea (SRA...

... program followed, challenges faced and results of polymer flooding. chemical flooding methods injector polymer concentration water cut upstream oil & gas polymer flooding active bottom water drive bechraji degradation breakthrough producer heavy oil polymer pilot petroleum engineer...

... into three modules: Injector-producer connectivity Injector efficiency Injection water optimization First module uses four major data types to estimate the connectivity between each injector-producer pair in the reservoir: Producers data (pressure, WC, GOR, salinity) Faults presence...

... A smart segmented injection technique was conducted in a test area in Daqing oilfield of China. The oil-bearing area is 6.4 km 2 . Since 2011, the polymer flood pattern has been put into production. The five-spot area pattern was adopted. The average distance between injector and producer...

...) Connectivity solver module – where connectivity between injectors and producers is quantified using a 2 year history match period, 2) Fractional Flow solver module – where oil rates are established as a function of injection rates, 3) Verification module – which is a blind test to assess history match quality...

... production enhancement efficiency injector producer watercut oil production workflow production monitoring downhole intervention upstream oil & gas attic oil column injection rate visualization dashboard facility management wrfm opportunity identification wof module Introduction...

... matching. Reverse here means making reservoir pressure as main constraint rather than history matching goal. After that, it was continued with water injection flow path analysis. This was done by plotting production-injection-pressure data then make several small groups of injector-producer based...